North Texas' (DFW's) Largest Custom Sign Builder Since 1979
WHOLESALE TO THE PUBLIC!
We Build and Install within 50 Miles around Richland Hills.
TURN-KEY Sign Design, Manufacturing, Installation, and Service
North Texas' (DFW's) Largest Custom Sign Builder
WHOLESALE TO THE PUBLIC!
Summary - Pylon Signs For Businesses
The Special Features and Benefits of Signs Manufacturing Corporation's Pole Signs and Pylon Signs
Lasting Quality – Your Sign will ALWAYS look good to potential customers
Structural steel frames with aluminium exterior skins – No rust and the sign will last forever. Virtually Hail-proof.
Computer-generated graphics – Perfect look, not handmade, much more impressive graphics.
Signlux Paint Systems™ Automotive+ paints and 2 part primer system - The same exterior paint type they paint a Ferrari with. It looks new virtually forever, helping your business.
Cabinet insides painted with Solar Finishes™ Bright Reflective White – Because of this special paint the sign always lights brighter, attracting more attention, with no additional electrical cost.
Impact-modified plastics - Won’t break and look bad.
SolarGuard™ protected plastics - Won’t fade and look bad to customers.
Lumabrite™ coated plastics – Because of this coating the sign always looks brighter with no additional energy cost.
Optigard™ coated flexible sign faces – This coating eliminates yellowing, which makes a sign look old and dingy, chasing potential customers away.
Vandal resistant coatings – Your sign won’t be intentionally damaged.
Self-cleaning sign faces – Your sign never looks dirty and dingy, chasing potential customers away.
Brighter Signs™ technology – Brighter signs always draw more attention.
Energy Saving Signs electrical – Saves 35% or more of electricity costs, some signs can even be solar powered.
UL or ETL listed sign – Can be legally installed anywhere, and moved anywhere at a later time.
Automatic Factory-Calibrated Electronic Lighting Controls – Automatically turns the sign “on” and “off” any time lighting will draw more attention to your business.
One-Stop Shopping - We design, engineer, permit, manufacture, install, even service these signs. Brick, masonry and concrete too.
The Special Features and Benefits of doing business with Signs Manufacturing™
We sell our signs FACTORY-DIRECT, WHOLESALE to the public,
INSTALLED.
Guaranteed Highest Quality...Guaranteed Lowest Price™ - We manufacture the best signs, for the lowest price.
WHOLESALE TO THE PUBLIC!
The Largest Custom Sign Company in the D/FW Metroplex - We can handle your needs. With about 200 custom signs in construction all the time we have the facilities and people to solve problems and get the job done; creatively. No one else comes close - no matter what they say!
We Actually Manufacture the Signs, Locally – Single-source responsibility. No middlemen.
Turn-Key™ Full-Service Sign Company – We manufacture, install, and service all signs; ours and others. Seven cranes/bucket trucks to 80' reach. Seven installation/service crews.
Visit Texas' Largest Signs Showrooms
-
Don't buy your sign from a drawing, a slick website, or photo-shopped
pictures, when you can actually see and side-by-side
compare Real signs and designs.
ImageKrafters™ Design Consultants and The Design Tank™ Digital Design Studio – Hundreds of years combined experience. Creative sign designs that make our customers more successful.
Day-Light Designs™
– Take full advantage of our automatic lighting controls and our SolarBrite™
LongLife™ LEDs to draw even more attention to your business. BETA TEST
Professional Market Research Consultants – Helping insure that your signage meets your needs.
Lifetime* Warranties – Save you money forever.
Product Liability Insurance – Protects you and your customers forever.
Deposit Insurance – Your money is protected even if we were to default.
Established 1979 – We back our claims.
Eleven Person Your-Location Sales Team – At your location to help you anytime we are needed.
Exclusive Automatic Updates System - Keeps our customers informed, so they know where their sign is in production, when the permits were approved and when the sign is scheduled for install.
State Licensed Electrical Sign Contractor – We know our business and do our job.
State Licensed Electrical Contractor – We know electricity.
Trained QualityCertifiedSigns™ Technicians – We understand quality.
Electronic LED Sign Experts – Because we manufacture them, we also know how to fix them all.
Many Different Payment Options – Cash, Credit Card, Conserve Your Nest Egg™, Signs on Time™ Lease (with Zero Down option) and Pay as You Grow Lease/Purchase™
Delayed-Deposit Billing™ - Significantly reduced initial billing to help you control your cash-flow.
Grand Opening Package* - We want you to be successful; here's another way we're helping. A free "Coming Soon" and "Grand Opening" banner with your name on it, and free "store" hours lettered on your door. *Minimum order required.
The Knowledge Tree™ - The world's largest and most complete information source on signage. (See below.)
"Sign Buyer's Guide" Brochures - How signs should be built, and why. Sign-type-specific printed information to help you purchase adequate signage. (See below.)
SignDawgsTV™ - Free Advertising every time your signs are featured in episodes!
The Signs Manufacturing Your-Location Sales Team'sPersonalized Service
No matter what types of signs you are interested in, our sales team, consisting of 11 highly-trained individuals, is at your beck and call.
Let us meet with you in your office, or at your new signs location, or home, or anywhere.
You will probably have a firm quotation, not a non-binding "estimate" like most competitors provide, for what you want during our meeting; certainly no more than a day later.
We can design and build your next sign while maintaining Social Distancing guidelines
Our Showroom is open and sanitized so you can safely review the different options available for your new signage.
Also, we have many options to help design your new look, from collaborating remotely (from your own home bridged to our design team) to designing with you in our Projection Room, which is large enough to maintain Social Distancing.
Pole Sign vs. Monument Sign - Do you have a choice?
If you have a choice, install a pole sign! You will be glad you did.
McDonald’s says that, on-average, simply replacing a monument sign in front of
one of their restaurants with a pole sign increases that store’s sales volume
15%.
Are You a "Visual" Person?
It is difficult to picture what a sign is going to look like. What do you picture when we say "triple-layer multi-colored lighting with a textured backplate?"
Our showroom is designed to solve that problem. Most people are visual ... they need to see something firsthand to understand what it is and whether it has value to them. Seeing is believing!
Don't buy your sign from a drawing, a slick website, or photo-shopped pictures, when you can actually see and
side-by-side compare Real signs and designs.
Unique in the entire sign industry, Signs Manufacturing™ built an 85’ by 50’ (over 4,000 sq ft) indoor sign lighting laboratory for testing the longevity, visibility, and effectiveness of all the lighted signs we manufacture. The Laboratory is open to the public, for FREE.
Don't buy your sign from a drawing, a slick website, or photo-shopped pictures, when you can actually see and side-by-side compare Real signs and designs.
Thousands of visitors have learned about sign design, materials, construction, lighting; and their effect on a business.
We invite you to also observe all other types of signage, viewing them up close as well as from a distance, under varying light conditions (and stay out of the weather while doing so!)
Pylon signs.
Pole signs.
Masonry Monument signs.
Cabinet signs, fluorescent, HID, or LED lighted.
Pinlights™ signs.
Wall-wash back-lighting for all types of signs.
Routed sign faces for all types of signs.
Digitally printed and cut vinyl decorated sign faces for all types of signs.
Acrylic-faced signs.
Lexan®-faced signs.
Flex-faced cabinet signs.
Push-thru lettering.
Computer-controlled full-color, programmable, building lighting.
Storefront Lighting.
Facade Lighting.
Neon and LED building accent lighting.
Wall-wash back-lighting for all types of signs.
SpectraLites™ Color-changing lighting.
SolarBrite™ LED lighting.
Neon and LED building accent lighting.
Neon color selection.
Brighter Signs™ neon.
LED color selection.
Channel letter signs, both neon and LED lighted.
Letterlites™ channel letter signs.
Twinkling Letterlites™ channel letter signs.
SpectraLites™ Color-changing channel letter signs.
How will shadows affect my sign's readability during the day? Should the wall behind my sign be light or dark colored? Would a different type of sign look better on my brick wall? Should I consider a routed sign face with push-through letters?
Don't buy your sign from a drawing, a slick website, or photo-shopped pictures, when you can actually see and side-by-side compare Real signs and designs.
Live Showroom Demonstrations of Products that Improve Your Signs
No one else can offer you this unique opportunity. Be sure to take advantage.
Your business will be better because you do.
If you don't visit it could cost you thousands in sales every year.
Can you afford not to?
"I almost made a huge mistake by not listening to you and visiting your showroom prior to buying my sign. I thought I knew what I wanted, after listening to so many salespeople...boy, was I wrong. My vision of the sign did not jibe with what it would really turn out to be, even after viewing so many drawings. It was obvious the moment I entered the showroom. If I had stuck to my guns my sign would have been a disaster. I would have wasted a lot of money." - Cecil Drake, Drake Communications
Showroom Specials
Sometimes it really pays to shop.
As an additional enticement to coax you into our showroom, and also smooth our manufacturing flow, we periodically have limited Specials only available "in-store;" even unannounced to our sales team.
They are based on opportunities in our production scheduling. If we tell our salespeople in advance they collectively sell too many, causing other problems!
Specials are always for a specific type of custom-built sign with a large variety of available options, but a very limited quantity, and first-come-first-served.
As detailed below, and on the pages that follow, everything will be done to make your sign look better, and last longer...Guaranteed.
WHOLESALE TO THE PUBLIC! Signs Manufacturing™ also guarantees that our price will be the lowest price you can obtain on the products described in this website; now or anytime during the next 90 days.
If you are offered a lower price by someone else we will match that lower price PLUS give you 10% of the difference.
"Fifteen years ago you made a lighted sign for me. It STILL looks new, but finally needs electrical service..." Lawrence Badger, M.D.
Full-Color & Monochrome Digital LED Electronic Message Centers & Video Displays in Pole Signs and Pylon Signs
If you would like to see if an LED sign is will be beneficial to your business, and how much it will cost, Contact Us for a free, no obligation quote and analysis of your business, projected increase in sales (based on Small Business Administration numbers), traffic counts in your area and the cost of a new sign.
Recognize that there is documented evidence that simply
adding a Digital LED Sign increases a businesses entire sales volume 15 - 150%.
Why Buy Factory-Direct from a State-Licensed Company?
Why not buy from a Sign Dealer (also called a Sign Broker, Car Wrap company or a Sign Store?)
Would you give a car dealer $10,000 and tell him to buy you the best car he can for the money, sight unseen (or from a drawing?) Don’t you think you would get the car that made him the most?
Do you think you could meet your needs asking for the cheapest car he can buy?
Why would a sign dealer (Car Wrap company or sign store) be any different? Remember, they are merely buying a sign from a manufacturer to resell to you, usually to resemble a drawing, making the most money they can.
You need to know ALL of the details on how your sign will be manufactured, and how it will be installed. It needs to meet YOUR needs, not the seller’s profit goals. What is he telling the manufacturer you don't need?
Believing “...a sign is a sign” gets you a Yugo instead of a Cadillac. Remember the Yugo? They didn’t last very long, either.
Also, most sign dealers, Car Wrap companies and sign stores cannot legally install or service an electric sign. Ask to see their license.
Ask to see a manufacturer's license also. A few are not licensed to do electrical work, either, they also have to hire other companies to install the signs they make.
Now, who provides the warranty? The manufacturer, the installer, the salesman, anyone? If the sign was installed illegally do you think they'll honor their warranty? Did they REALLY obtain your City sign permit? Is the sign even safe?
As a large, both UL and ETL listed manufacturer, our name is on all our signs. Just like you, we can't afford to have a bad sign destroy our business. We have to care. Particularly with our 1 Year Warranty and Lifetime Guarantee*.
The State of Texas does NOT allow the installation on non-Listed electrical signs, and a Texas Sign Contractors License (TSCL) is not evidence of an OSHA approved Listing for electrical signs. Additional approvals are required.
Why are “Listed" Pole Signs Critical to You?
Virtually ALL cities, as well as the State of Texas, adopt the National Electric Code as law.
The National Electric Code (NEC) requires that for electrical, structural, and installation safety all electrical signs be "Listed" (tested and labelled with an appropriate Listing Mark.)
Certification (testing and labeling) organizations acceptable in the USA to test to the multitude of Standards signs are required to meet are determined by OSHA.
For you the Listing Mark is insurance. It means that the sign has been tested to insure that it is structurally and electrically safe, and will be installed properly. You benefit from the knowledge that it is not solely us telling you that our signs are safe, this is what the testing laboratories and the US Government says also.
Will your sign be tested and approved for safe use in a Wet (Outdoor) location? Not if it’s not Listed!
If the sign you are purchasing does not have a ETL or UL Listing Mark label the sign is probably not legal to install, anywhere in Texas. There are a few local city ordinance exceptions.
Buy carefully.
For more detailed information on "listing and labeling" click on the "Labeled and Listed" tab in the Knowledge Tree™ tab in the left column.
Construction
For strength, durability, and appearance your illuminated signs will be constructed of aluminium (#3003, H14 - not the "soft" aluminium used by some) covering a welded structural-steel inner frame.
Large metal areas will be reinforced to prevent "oil-canning".
The structural-steel frame inside the sign is separately painted before the skins are installed; important to prevent rust stains later.
We commonly build pylon signs with real and artificial brick, stone, and stucco exterior finishes. View our "Bricks & Masonry" page, tabbed to the left.
Our signs are properly engineered to withstand the winds of North Texas (140 m.p.h.); signs attached to poles are welded, not bolted, in place.
A Warning About Some Very-Substandard Signs
Some companies use plastic, Dibond and ACM-type products for their
cabinet skins.
Your Texas sign gets heated! Dibond and ACM Sheets
(Aluminum Composite Materials) which sandwich polyethylene between two
thin sheets of aluminum are especially subject to warping.
Plastics and metals expand and contract at different rates. With
Dibond and ACM-type sheets used outdoors, because they are made of two
dissimilar types of materials (plastic and aluminium) warp with
temperature, hot and cold. They are not designed for this application, but some
sign companies manufacture outdoor signs using them.
They
shouldn't.
Certified Welding
We employ Certified Welders. Horizontal, vertical, and overhead.
We are virtually the only sign company in the Dallas/Fort Worth Metroplex employing certified welders.
The Importance of Sign Thickness
The thickness of a sign does more than impart a more prominent importance to a sign, it affects the graphics.
The minimum allowable thickness of a sign depends on the type of internal lighting and the type and size of the sign face.
Lighting and sign face types will be discussed later.
The larger the sign face the thicker a properly made sign cabinet must be.
It is very important that the sign be thick enough that the lighting in the sign does not show as “hot spots” or “zebra striping” on the face of your sign. Either of these makes your sign look “cheap” no matter what its cost. In some instances these can be so bad that a sign is not readable at night. You’ve seen them.
All of this makes the use of extruded aluminum sign frames problematic in building a quality sign, to say nothing about a strong sign (no structural steel inner frame) since extrusions are only available for limited cabinet depths; however some sign companies continue to attempt to do so. Signs Manufacturing™ does not use extruded cabinets precisely for these reasons.
We calculate what is required to make a proper and impressive sign for you, and then we build it.
It is more expensive to do the job right, but what is the value of a “cheap” sign that gives potential customers a negative impression of your business?
Retainer Types
There are two different retainer types, 3-D “Picture-Frame” retainers, and
“flat” retainers. Which one you choose can dramatically affect the appearance
of your sign. View these retainer styles in our Showroom to understand their
differences.
The Importance of Retainer Width
Equally important to the appearance of the sign is the width of the retainer (the ring of metal around the sign face that covers the mechanism that holds the sign face in the cabinet.)
This border plays a very important role in the apparent quality of your sign, and both size and color must be considered in the overall design.
This makes the use of pre-made extruded aluminum sign frames undesirable.
Tabs to other components of a pole/pylon sign are listed down the left side of this page.
Be sure to select the "Specifications"
tab in the left column. This is a tool for your use to insure that
quotations you receive are for the same sign!
The
Safety Feature of a Fixed Bottom Retainer
Unlike virtually all other manufacturers, we realize that if the bottom
retainer, which is simply screwed in place on most signs, falls off, a plastic
sign face also falls off; probably breaking. Our bottom retainer is a fixed
part of our sign, and is not removable without disassembling the entire bottom
of the sign cabinet. Much safer.
Soften
Your Signage if you Can
While
it usually costs more to manufacture a rounded-corner sign than a square-edged
sign, you should allow us to do so if your budget will allow. Why? Because
your sales will probably improve!
In the mid-1960’s Procter & Gamble changed the
labeling on their Tide® detergent. The new design eliminated the
round “target” in their logo. Sales immediately dropped. They immediately
redesigned the logo to add-back the round “target” and sales immediately jumped
back up, then increased. This revelation caused a revolution in car designs as
well as everything else.
Learn
from this; it is now a proven marketing fact that softer, rounded, less “sharp”
logos psychologically create a more favorable impression.
When Head & Shoulders® hair shampoo was
first being developed, samples were distributed to college students in both
rectangular and in rounded containers. Test results were that students loved
the product in the rounded containers, but thought that the product in the
rectangular bottles made their scalp itch. Have you noticed the round “swirl”
in the Head & Shoulders® logo?
Visit
our Showroom to compare multiple examples of signage with both “squared” and
“rounded” corners and “looks.” Decide for yourself before committing to a sign
design that can determine the success of your business.
Automatic Electronic Thermal Lighting Controls*
When our founder was very young he managed a
supermarket, a grocery store.
He discovered that he could affect the store's
business by simply turning “on” the store's signs on less-than-sunshiny days.
Cloudy and/or rainy days would have a higher sales volume than bright days,
IF HE REMEMBERED TO TURN THE SIGNS ON.
And with the tinted window glass so prevalent in
the South it is often-times hard to tell if a business is even open.
These are lessons every business person should
be aware of. And, with today's modern LED illuminated signage, it costs
practically nothing to make your store really stand out!
What is the main reason our Sunburst™
LED outdoor digital signs increase a store’s business so dramatically? Lighted
signs draw much more attention than unlighted signs, even during the day!
Because we recognize how important this is, we will
now install automatic electronic lighting controls on every lighted sign
we manufacture*, factory calibrated to turn the sign “on” and “off” at times when lighting will
help you do more business. Over the past 40+ years, we have documented EXACTLY
when a sign’s lighting should be turned “on” to increase visibility on dark
and/or rainy days, and exactly when at dusk a sign should be turned “on.” The
whole purpose of the sign, after all, is to attract attention to your business.
We make your sign both more attention-getting AND more legible.
The setting varies for signs pointed East, West,
North, or South, and varies for signs containing neon, HID lighting,
fluorescents, and/or LEDs. It also varies by how the sign was built. Optimum
settings are custom-set for every sign.
Another example of our doing everything we can to
insure that our signs make your business the most successful. As far as we know, no other sign manufacturer
does this, for free or otherwise, for their customers.
If possible, have your electrician also wire a time
clock to control the power supplying your signs. The time clock should be set
to keep the sign “off” at times they should never be lighted, say 2:30 AM to
5:30 AM, the rest of the time whether the sign is “on” or “off” should be
determined by our automatic lighting controls. USE ELECTRICITY WISELY TO MAKE
YOUR BUSINESS THE MOST VISIBLE, BUT CONSERVE ENERGY.
Regarding “Energy Consumption” note how little
energy our SolarBrite™LED
lighted signs use in a year!
Recognize that Intermatic and Tork time clocks,
used by most electricians, are not finely adjustable, and at certain times of
the year dawn and dusk occur at quickly-varying times, gaining or losing over 15
minutes of daylight each week. If you only have a time clock controlling power
to your signs, savvy business owners must reset their time clocks constantly and
carefully, and manually override them to turn “on” their signs on dark days.
Good luck getting your employees to do this religiously – THIS IS ALSO WHY WE
INCLUDE CALIBRATED AUTOMATIC THERMAL LIGHTING CONTROLS ON EVERY OUTDOOR SIGN WE
MANUFACTURE.* Incidentally, we DO NOT use photo cells or photo eyes. They
are neither precise nor reliable.
Anecdotal data suggests that increased profits
resulting from this feature alone more than pays for the entire cost of most
signs EVERY YEAR.
Unconvinced of the importance to you? View our
control system in operation, and our supporting testing, in our Sign Lighting
Laboratory and Showroom. Then you can decide if you agree that this is a
critically important improvement in signage effectiveness.
*Dependent on size and design.
The failure mode for our automatic electronic lighting controls is “always on.”
You will never be without an attractive sign if something should break; you’ll
spend a little more on electricity until we get it fixed.
What
are Day-Light Designs™?
Knowing that our signs will be illuminated during
the day we design our signs and lighting for daylight effectiveness; to take
full advantage of our daytime lighting.
For instance, we pack backlighting to create a
subtle glow during the day. If you are going to light a sign during the day the
lighting better look good!
This is easier to accomplish when we incorporate our SolarBrite™ LongLife™
LEDs which are so much brighter than competitive LEDs.
If we didn’t use SolarBrite™ LEDs we couldn’t design and build signs that
offered such an advantage when compared to competitive signs (Both our
competitors, and your neighbor’s signs.) We don’t waste electricity, simply
because our signs always stand out, even when both are lighted.
“We prosper because of our sign. Signs Manufacturing’s unique understanding of the use of colors and light both day and night causes our business to always be the most visible. No one else could work their magic!” – the 407 club
Free Factory Tour
Come and see the array of equipment and tools, and the facility dedicated to making good signs.
Contact a sales consultant to arrange a plant tour.
We are a full-service sign company. We provide sign site surveys, sign permits, sign installation and sign maintenance services for electrical and non-electrical signs for our customers as well as other sign companies. We provide this work in Dallas, Fort Worth (DFW), and ALL of North Texas and Northeast Texas.
State Sign and Electrical License Numbers: TECL17503, TSCL18015, TSCL18016.
Our technicians are also Quality Certified Signs™ certified. (Click the "Installation & Service" tab for details.)
The Quality Certified Signs™ Difference – People You Can Trust
Quality Certified Signs™ is a training, certification, and continuing education program designed to train all sign company personnel to take better care of their customers utilizing knowledge-based performance.
Certifications are available in:
OSHA 10 Certification
Master Cabinet Maker
UL Listed Sign Technician
ETL Listed Sign Technician
ESA Listed Sign Technician
Certified Welding Technician
Wall Sign Installation Technician
Detached Sign Installation Technician
Interior Sign Installation Technician
Sign Service Technician
Electronic Message Center Specialist
Sign Mechanical Technician
Rotating Sign Installation/Service Specialist
High-Rise Installation/Service Specialist
State Licensed Sign Electrician (Texas)
Fluorescent Lighting Technician
Neon Lighting Technician
LED Lighting Technician
HID Lighting Technician
Incandescent Lighting Technician
Sign Design Specialist
Vinyl Application Technician
Graphics Technician
Painting Technician
Quality Control Technician
Crane Operator
Vehicle Operator
Fork Lift Operator
CNC Equipment Operator
ALL our personnel are Quality Certified Signs™ qualified because we also want the job done right.
The organizations that assist in developing and monitoring Quality Certified Signs™ training programs:
Sign Cost Information
We sell our signs FACTORY-DIRECT, WHOLESALE to the public,
INSTALLED.
No middle-man profits.
Click the "Cost" tab under the "Pricing" tab to the left that lists general budget pricing for pole and pylon signs.
Use our Payment Plan Calculator™ to estimate YOUR lease cost, and our Sign Cost Calculator™ to estimate your after-tax cash-purchase sign cost. They are located on our "Cost" page. Or, ask our salesperson to run the numbers for you.
When you do so notice how dealing directly with the manufacturer can potentially save you additional dollars in sales/use taxes!
But, please, contact us to develop an exact plan to meet your particular needs - for free (see our "Design Center" page!)
Our professional staff will usually have exact quotations, and exact scale drawings of your signs installed on your building or property ready for you the same day we meet with you. (Much faster than the 2 1/2 week average in our industry.)
If you are planning for the future, please bookmark our website as a "Favorite" so you can find us when you are ready.
"Look at that sign, it's like made out of plastic!" - Jon Taffer, Host of Bar Rescue
"If they put that little effort into their sign, I'd hate to see what they put in their food." - Nick Liberato, Celebrity Chef and Owner/Operator of Calidelphia Catering
"...but look at that sign, it only faces one way! They're turning their back on 13,000 cars every day!" - Jon Taffer, Host of Bar Rescue
Using Our Website to Learn | The Knowledge Tree™
Your sign forms that very important "first impression" your potential customer has of your business. Your sign must always look nearly as good as it looked the day it was installed so that you don't give potential customers a worsening impression of your business as your sign ages.
An example of our dedication to helping our customers succeed is this website. It IS the definitive source on signage information, ranked by Alexa® in the top 0.05% of ALL websites in the world, the top 0.01% in the USA!
We call our website The Knowledge Tree™. Online since 1997, this website is full of information regarding signs. Our database to create it requires over 8,000 pages; more information than some "encyclopedias."
The Knowledge Tree™ tells you how we manufacture our signage, and why.
Knowledge Tree™ links are on the left side of every page. For instance, click our "Types of Signs" button, then pick any of our products, and explore that page's tabs and discover how we make each sign to last; including the use of CNC manufacturing, rust-proof metal, structural-steel frames, high-end automotive paint, high-impact plastics, and most importantly, sophisticated protective coatings.
Go to our "About" page and select tabs to learn about the history of Signs Manufacturing, and many other subjects.
Unsure, or unconvinced about the importance of signage to the survival and success of a business? Click our "About" page's "Importance of Signage" tab.
Please use and enjoy this 550+ page website with over 3,000 images, the largest information resource about signs on the internet, created so you can learn about all types of signs and how you can control their affect on your image and business. Consider "bookmarking" our site as a "favorite" for easier reference later.
We believe that if you're a knowledgeable purchaser there's a real good chance you'll become our customer.
Signs are Like Boats
There are $50,000 boats and there are $400 boats. Technically both are boats, but don't expect that $400 boat to keep your business afloat. The devil is in the details.
If a company goes to the cost and effort of adding value to their product (types and amount of lighting, paints, protective coatings, etc.), they're going to talk about it. Pay attention to what they aren't telling you.
Our websites, literature and proposals describe in detail what we are quoting, and why we are doing it.
Nobody ever includes quality and features in their products that are not described in their literature and quotations.
Have you had a different experience?
Consider how important a quality sign, being the first thing your customers see of your organization, is to your success.
Buyer Beware! Nothing hurts a business more than bad signage.
Literature
We believe we are the only sign company that offers informative literature on signage, our "Sign Buyer's Guide" series.
Our most popular Guides are:
LED Signs
Full-Color or Monochrome
Lighted 3D Channel Letter Signs
Wall Cabinet Signs
Pole Signs and/or
Pylon Signs
Monument (Ground) Signs
Lobby and
Reception Signs
44 Page Brochure
40 Page Brochure
40 Page Brochure
40 Page Brochure
40 Page Brochure
20
Page Brochure
Additional "Sign
Buyer's Guide" Literature Available:
Signs Manufacturing's production facility is located at 4610 Mint Way, Dallas, TX 75236.
| Sales@SignsManufacturing.com
Business Hours: 07.00 a.m. to 5.00 p.m. Monday thru Friday (Central Time) or by Appointment. Office Hours: 08.00 a.m. to 5.00 p.m. Monday thru Friday. Showroom hours are by Appointment. Factory Tours by Appointment. Emergency Service 24/7.
Exclusive Automatic Updates System - Keeps our customers informed, so they know where their sign is in production, when the permits were approved and when the sign is scheduled for install.
Storefront Lighting.
both neon and LED lighted.
Certified Welding Technician
Our professional staff will usually have exact quotations, and exact scale drawings of your signs installed on your building or property ready for you the same day we meet with you. (Much faster than the 2 1/2 week average in our industry.)
